Show pictures:

Objective:

  1. Record your first installation
  2. Share the text version installation tutorial of this configuration, what should be paid attention to the first installation

Requirements:

  1. Graphics card with, so the CPU needs to take the core display, do not need to overfrequency.
  2. Black, no light pollution
  3. Start with 32GB memory
  4. Other accessories start with 3070 graphics card as standard (affecting power supply)
  5. Budget: around 5000 (laptop sold 5000 before)

Purchase order :(refer to the plan shared by the computer bar assessment room)

  • CPU: i7-12700-2419
  • Motherboard: ASUS TUF GAMING B660M-Plus WIFI D4 Heavy Gunner motherboard costs 1018
  • CPU heat dissipation: Limin PA120 costs 192
  • Graphics card: no cost 0 [* default network 30 mine card, ha ha ha]
  • Power supply: Xingu GN750 costs 483
  • Solid: the previous Purcott 1T cost 0 (may require additional heat dissipation armor)
  • Memory: Kingston 3200 DDR4 16*2 costs 967.5
  • Case: Aigo K100 (mainly focused on the front Type-C, mute) costs 385.5
  • Total cost: 5,465

Correct process after installation:

  1. To prepare

    1. Screwdriver (preferably long)
    2. Rubber gloves (I am afraid of static electricity, do not know if it is necessary)
    3. Check accessories: CPU, motherboard, memory, hard disk, power supply, fan, case, independent graphics card (if any, if not require CPU with core display, like my 12700)

  2. Load the accessories on the motherboard (mine is ASUS TUF GAMING B660M-Plus WIFI D4 heavy gunner)

    1. Install CPU (I7-12700), note:

      1. Pay attention to their CPU with the motherboard is compatible (this should be paid attention to before buying, to avoid a miracle)

      2. Open the hook on the motherboard, put the CPU straight (four corners with a triangle on the motherboard to its. You can also look at the direction of the word on the CPU, if it is positive.

    2. Install memory, note:

      1. I installed slot 1, 3 for the first time, the result after opening XMP, open the opportunity to report an error. Search said to be in 2, 4 normal, said the motherboard BUG?
      2. But I also reported errors on 2 and 4, and then I manually set 3200

    3. Install hard disk, note:

      1. I am an M.2 and a SATA3 with two solid states (M.2 is installed in the place with heat dissipation waistcoat, and SATA3 is installed on the back of the chassis).
      2. The problem is that the U disk is always turning when installing the system, and I checked that it was caused by two disks, so I disconnected the SATA3 disk and entered the stage of installing the system. (said to be installed after the street SATA3 disk on the line, but I do not know why not, may be because my disk is not formatted?)

  3. Install the motherboard into the case, note: \

    1. The chassis has a few screw openings by default, but the positions may need to be adjusted according to the motherboard. There are only 4 corresponding ones on this motherboard, which need to be manually adjusted (there are screws in the chassis accessories).

  4. Install the power supply to the chassis, note: in fact, the main attention is to install the power line support the chassis fan power supply, hard disk power supply, video card power supply, CPU power supply, etc. As shown in figure:

  5. The cable of the chassis is connected to the motherboard. Note:

    1. Which cables: Boot, reboot, Indicator, USB, Type-C, audio, LED (I don’t have one)

  6. CPU fan, suspended solid state connection.

    1. CPU Fan Connection

      1. First put the shelf

      2. Place the combination of heat sink and fan (refer to the fan manual here, and pay attention to the air inlet and outlet of the purchased fan)

        1. Apply thermal grease first

    2. Suspended solid state connection

      1. Notice Power supply + data port

  7. Ready to install the system?

    • Use method: U disk Microsoft Assistant install W11
    • Points to note:
      1. If you only hang one M.2 solid, two of them will get stuck in loading the logo and turning around
      2. The best way to connect the monitor is 1080P. (I started with 4K, and the HDMI cable didn’t get into the BOST setup page, nor did the system setup page. It is ok to change the wire with PD1.2. But when it comes to the end of the installation, it becomes a screen, and the HDMI cable can be = =, bought a PD1.4 is still on the road I do not know how to do)
      3. After installing the system, you need to go to Inter to update the core driver, otherwise LOL will only be 10 FPS
      4. Note that when updating the driver, do not use a third party driver to update the audio (such as driver wizard, 360 driver, Master Lu) after their update of the audio driver, the microphone failure, I do not know how to solve (check online method is not good) and finally reinstall the system to solve = =
      5. BOIS started the XMP of the memory module and the computer reported an error. I ended up setting it manually

  8. Personal Installation review:

    1. Time line:

      1. The first day on the ground squat for one day installation, resulting in the second day and the third day leg pain, the need for enhanced exercise
      2. The next day after installing the system, I directly downloaded LOL and opened LOL with my friends. At this time, I did not pay attention to the graphics card driver version, and the normal game could not be played with only 10 FPS, which led to the failure of the game
      3. The next day when I updated the driver, I did not carefully check what was updated, resulting in the update of the audio driver and the failure of the microphone. So find a way to waste time, and finally reinstall the system to solve
      4. Day three… Well, the third day is to reinstall the system game —

    2. Heart course:

      1. Before the installation: feel small understanding, hands-on ability is also good, take the morning express installed after the afternoon can install the system, download the game, happy night open black
      2. Installed in: this is what, that is what, this why of, that why of, connect where, where
      3. After loading: no, reloading
      4. After installing: walk line really ugly, tired dead
      5. Before system installation: easy (laptop installed many times before)
      6. When installing the system: why doesn’t the screen light up
      7. After installing the system: ok
      8. Install the system to use: zha again a problem, reinstall
      9. Install system flow again –
      10. The JD199 installation system might be worth it

    3. Feelings: although the front and back spent a lot of time, but still very worthwhile, after all, the first time, the next charge 200 to engage in sideline ~